View FTM-9712P-F20_4750465.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Mar. 20, 2007
2x5/2x10 SFF GEPON OLT Transceiver FTM-9712P(T)-F(K)20(G)
(IEEE 802.3ahTM-2004 1000Base-PX20-D)
Members of FlexonTM Family
Standard
Compliant with SFF MSA Compliant with IEEE 802.3ahTM-2004 Compliant with FCC 47 CFR Part 15, Class B Compliant with FDA 21 CFR 1040.10 and 1040.11, Class
Features Description
Single fiber bi-directional data links with symmetric 1.25Gbps upstream and 1.25Gbps downstream Integrated with micro-optics WDM filter for dual wavelength Tx/Rx operation at 1490/1310nm 1490nm continuous-mode transmitter with DFB laser 1310nm burst-mode receiver with APD-TIA Optical isolator built in for extreme Return Loss tolerance Resetless burst-mode receiver design Support more than 24dB dynamic range 0 to 70C operating temperature Optional 2x5/2x 10 SF F package with SC/UPC and SC/APC pigtail Single 3.3V power supply LVPECL compatible data input/output interface LVTTL transmitter disable control LVTTL transmitter laser failure alarm (P-K20(G),T-K20(G)) LVTTL receiver signal-detected indication Low EMI and excellent ESD protection Classlaser safety standard IEC-60825 compliant RoHS compliance (FTM-9712P(T)-F(K)20G) FTM-9712P(T)-F(K)20(G) is Optical Line Terminal (OLT) compliant with 1000BASE-PX20 application. The transceiver is the high performance module for 1.25Gbps data link in single fiber by using 1490nm continuous-mode transmitter and 1310nm burst-mode receiver. The transmitter section uses a multiple quantum well 1490nm DFB laser and is Class laser compliant product according to international safety standard IEC-60825. The receiver section uses an integrated 1310nm PIN diode and preamplifier mounted in an optical header and limiting post-amplifier IC. Unlike the conventional burst-mode receiver, the receiver does not require reset pulse to receive optical data packets with different optical power. The optical output can be disabled by a LVTTL logic high-level input of TX_DIS. LAS_nFAIL is provided to indicate that degradation of the laser (2x1 0 SFF ). Signal Detected (SD) output is provided to indicate the detection of an input optical signal of receiver.
Applications
Gigabit Ethernet Passive Optical Networks (GEPON) - OLT side Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 1 of 13 Doc No: DS3513000-1d
2x 5/2x10 SFF GEPON OLT Transceiver 20km transmission
FTM-9712P(T)-F(K)20(G) Preliminary Data Sheet Mar. 20, 2007
Regulatory Compliance
The transceivers have been tested according to American and European product safety and electromagnetic compatibility regulations (See Table 1). For further information regarding regulatory certification, please refer to FlexonTM regulatory specification and safety guidelines, or contact with Fiberxon, Inc. America sales office listed at the end of documentation. Table 1 - Regulatory Compliance
Feature Electrostatic Discharge (ESD) to the Electrical Pins Electromagnetic Interference (EMI) Immunity Laser Eye Safety Component Recognition RoHS MIL-STD-883E Method 3015.7 FCC Part 15 Class B EN55022 Class B (CISPR 22B) VCCI Class B IEC 61000-4-3 FDA 21CFR 1040.10 and 1040.11 EN60950, EN (IEC) 60825-1,2 UL and CSA 2002/95/EC 4.1&4.2 Compliant with standards Compliant with Class I laser product Compliant with standards Compliant with standards Compliant with standards Standard Performance Class (>500 V)
Absolute Maximum Ratings
Absolute Maximum Ratings are those values, beyond which, some damage may occur to the devices. Exposure to conditions above the Absolute Maximum Ratings listed in Table 2 may negatively impact the reliability of the products. Table 2- Absolute Maximum Ratings
Parameter Storage Ambient Temperature Operating Ambient Temperature Operating Humidity Power Supply Voltage Input Voltage Receiver Damaged Threshold Soldering Temperature Bending Radius Pigtail Fiber Contact Temperature 30 85 Symbol TSTG TOPR HOPR VCC Min. -40 0 5 0 GND +4 400 260/10 Max. 85 70 95 4 VCC Unit C C % V V dBm C C/s mm C 2 3 Note 1
Note 1: When ambient temperature is above 60C, airflow at rate higher than 1m/sec is required Note 2: Only for soldering by iron and 10 seconds on leads only (for FTM-9712P(T)-F(K)20). Note 3: Soldering on lead only (for FTM-9712P(T)-F(K)20G). Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 2 of 13 Doc No: DS3513000-1d
2x 5/2x10 SFF GEPON OLT Transceiver 20km transmission
FTM-9712P(T)-F(K)20(G) Preliminary Data Sheet Mar. 20, 2007
Recommended Operating Conditions
Table 3 - Recommended Operating Conditions
Parameter Power Supply Voltage Operating Ambient Temperature Operating Humidity Range Data Rate Data Rate Drift -100 Symbol VCC TOPR HOPR Min. 3.13 0 5 1.25 +100 Typ. 3.3 Max. 3.47 70 95 Unit V C % Gbit/s PPM Note 3.3V5% 1
Note 1: When ambient temperature is above 60C, airflow at rate higher than 1m/sec is required
Optical and Electrical Characteristics
Table 4 - Transmitter Optical and Electrical Characteristics (0C Parameter Optical Center Wavelength Optical Spectrum Width (-20dB) Side Mode Suppression Ratio Average Launch Power Average Launch Power-OFF Transmitter Extinction Ratio Total Jitter Rise/Fall Time (20%-80%) RIN15OMA Optical Return Loss Tolerance Transmitter Reflectance Transmitter and Dispersion Penalty Optical Eye Diagram Data Input Differential Swing Input Differential Impedance Power Supply Current Transmitter Disable Voltage - Low Transmitter Disable Voltage - High Laser Failure Alarm Voltage - Low Laser Failure Alarm Voltage - High VIN ZIN ICC_TX VTDIS, L VTDIS, H VLFA, L VLFA, H 0 2.0 0 2.4 TDP 200 90 100 Symbol C SMSR POUT POFF ER TJ TR/TF 9 0.43 260 -115 12 -10 2.3 Compliant With IEEE Std 802.3ahTM-2004 1600 110 200 0.8 VCC 0.4 VCC mV mA V V V V 7 8 30 +2 +7 -39 Min. 1480 Typ. Max. 1500 1 Unit nm nm dB dBm dBm dB UI ps dB/Hz dB dB dB 4 2,5 6 1 2 2.3 Note
Note 1: Launched into 9/125um Single Mode Fiber. Note 2: Measured with PRBS 27-1 test pattern @1.25Gbit/s. Note 3: Measured with the Bessel-Thompson filter OFF. Note 4: Maximum sensitivity penalty due to transmitter and dispersion effect through 20km of SMF optical fiber. Note 5: Transmitter eye mask definition {0.22UI, 0.375UI, 0.20UI, 0.20UI, 0.30UI}. Note 6: Compatible with LVPECL input, AC coupled internally. (See Recommended Interface Circuit) Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 3 of 13 Doc No: DS3513000-1d
2x 5/2x10 SFF GEPON OLT Transceiver 20km transmission
FTM-9712P(T)-F(K)20(G) Preliminary Data Sheet Mar. 20, 2007
Note 7: TX_DIS (See Pin Function Definitions) Note 8: LAS_nFAIL, for FTM-9712P(T)-K20(G) (See Pin Function Definitions) Table 5 - Receiver Optical and Electrical Characteristics (0C Parameter Operating Wavelength Sensitivity Saturation Receiver Threshold Settling Time Dynamic Range Signal-Detected Assert Level Signal-Detected Deassert Level Signal-Detected Hysteresis Receiver Reflectance Power Supply Current Data Output Voltage - Low Data Output Voltage - High Data Output Differential Swing Signal-Detected Voltage - Low Signal-Detected Voltage - High Signal-Detected Assert Time Signal-Detected Deassert Time
7
Symbol PSEN PSAT TSETTLING
Min. 1260 -6
Typical
Max. 1360 -30 250
Unit nm dBm dBm ns dBm dBm dBm dBm dB mA V V mV V V s s
-12
Notes
1 1,2 1,3 4 5
-30 PSDA PSDD PSDA- PSDD ICC_RX VOL-VCC VOH-VCC VOUT VSD, L VSD, H TASS TDAS -1.81 -1.02 400 0 2.4 1.2 0.5 -45 0.5
-6 -31 6 -12 120 -1.62 -0.88 1600 0.4 VCC
6 7
Note 1: Measured with a PRBS 2 -1 test pattern @1.25Gbit/s and ER=10dB, BER =10 . Note 2: See Figure 1,2. For multiple ONUs application, It isn't easy to test TSETTLING directly, but there is a relationship TSETTLING = TGAP-TGUARD when TON=TOFF, then TSETTLING can be calculated by TGAP and a certain guard time at ONU side. Note 3: See Figure 3. TGAP be less than 250ns is guaranteed. Note 4: An increase in optical power above the specified level will cause Signal-Detected (SD) output to switch from a low state to a high state. Note 5: A decrease in optical power below the specified level will cause Signal-Detected (SD) output to switch from a high state to a low state. Note 6: LVPECL output, DC coupled internally, guaranteed in the full range of input optical power (-6dBm to -31dBm) (See Recommended Interface Circuit) Note 7: SD (See Pin Function Definitions)
Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 4 of 13
Doc No: DS3513000-1d
2x 5/2x10 SFF GEPON OLT Transceiver 20km transmission
FTM-9712P(T)-F(K)20(G) Preliminary Data Sheet Mar. 20, 2007
Within 15% of Optical Steady State
Optical Signal Output (at ONU side)
Average Optical Power <=-45dBm
Upstream Data (TD+/TD- at ONU side)
TON Tx_BRST (at ONU side)
TOFF
TSETTLING Upstream Data (RD+/RD- at OLT side) Garbage Data
Valid Data
Figure 1 Timing Parameter Definition in Burst Mode Sequence (Sole ONU Application)
TX_BRST(ONU#1) TEN_DUR TX_BRST(ONU#2) TON1 TOFF1 TDIS_DUR
Optical Signal (ONU#1) At TP3
TGUARD
TON2
TOFF2
Optical Signal (ONU#2) At TP3 TO/E
Within 15% of Optical Steady State TGAP
Electrical Signal (OLT) At TP4
Figure 2 Timing Parameter Definitions in Burst Mode Sequence (Dual ONUs Application)
Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 5 of 13
<-45dBm
Doc No: DS3513000-1d
2x 5/2x10 SFF GEPON OLT Transceiver 20km transmission
FTM-9712P(T)-F(K)20(G) Preliminary Data Sheet Mar. 20, 2007
From Strong ONU(PO= -6dBm)
Optical Signal Input (At OLT Side)
24dB Optical Power Dynamic Range
From Weak ONU(PO= -30dBm)
Figure 3 Burst Mode Receiver Dynamic Range in GEPON System
Recommended Interface Circuit
Figure 4 shows the recommended interface schemes for FTM-9712P(T)-F20(G).
VEET(7) +3.3V 2x1uH 10uF 0.1uF 10uF PON_TX_DISABLE Z=50 0.1uF 0.1uF VCCT(6) VCCR(2) VEER(1) TX_DIS(8)
FTM-9712P(T)-F20(G)
+3.3V 1K
TXP TXN 2x150
TD+(9) TD-(10) 100
Z=50
CM Laser Driver
GEPON MAC
SerDes
+3.3V 2x130 RXN Z=50 Z=50 RXP 2x82 SD(3) RD-(4)
RD+(5) +3.3V 1K
BM Limiting Amplifier
PON_LOS
Figure 4 FTM-9712P(T)-F20(G) Recommended Interface Circuit
Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 6 of 13
Doc No: DS3513000-1d
2x 5/2x10 SFF GEPON OLT Transceiver 20km transmission
FTM-9712P(T)-F(K)20(G) Preliminary Data Sheet Mar. 20, 2007
Figure 5 shows the recommended interface schemes for FTM-9712P(T)-K20(G).
VEET(12,16) +3.3V 2x1uH 10uF 0.1uF 10uF +3.3V PON_TX_DISABLE 4.7-10K Tx_Fault(CPU IO) TXP Z=50 0.1uF 0.1uF VCCT(11) VCCR(7) VEER(2,3,6) TX_DIS(13) LAS_nFAIL(18) TD+(14) 100
FTM-9712P(T)-K20(G)
+3.3V 1K
TXN 2x150
Z=50
TD-(15)
CM Laser Driver
GEPON MAC
SerDes
2x130 RXN RXP 2x82
+3.3V Z=50 Z=50 RD-(9)
RD+(10)
BM Limiting Amplifier
+3.3V 1K PON_LOS Fiberxon Tuning Equipment SD(8) DEBUG_PORT#1 (19) DEBUG_PORT#2 (20) Note
Figure 5 FTM-9712P(T)-K20(G) Recommended Interface Circuit Note: Fiberxon reserve the two-wire debug port for module tuning. (DO NOT connect these pins to any circuit on host board)
Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 7 of 13
Doc No: DS3513000-1d
2x 5/2x10 SFF GEPON OLT Transceiver 20km transmission
FTM-9712P(T)-F(K)20(G) Preliminary Data Sheet Mar. 20, 2007
Pin Definitions
2x5/2x10 SFF planform in Figure 6 below shows the pin information of electrical interface and mounting studs. Functions are described in Table 6 with some accompanying notes.
Figure 6 2x5/2x10 SFF Planform
Table 6 - Pin Function Definitions
Pin No. 2x5 SFF No Pin No Pin No Pin No Pin No Pin 1 2 3 4 5 6 7 8 9 10 No Pin 2x10 SFF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 NC VEER VEER NC NC VEER VCCR SD RDRD+ VCCT VEET TX_DIS TD+ TDVEET No Function Definition Receiver Signal Ground Receiver Signal Ground No Function Definition No Function Definition Receiver Signal Ground Receiver Power Supply Receiver Signal-Detected Indication Inverted Receiver Data Output Non-inverted Receiver Data Output Transmitter Power Supply Transmitter Signal Ground Transmitter Disable Transmitter Non-inverted Data Input Transmitter Inverted Data Input Transmitter Signal Ground 3 4 1 2 Not connected Not connected Not connected Name Description Notes
Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 8 of 13
Doc No: DS3513000-1d
2x 5/2x10 SFF GEPON OLT Transceiver 20km transmission
FTM-9712P(T)-F(K)20(G) Preliminary Data Sheet Mar. 20, 2007
No Pin No Pin No Pin No Pin F
17 18 19 20
NC LAS_nFAIL DEBUG PORT#1 DEBUG PORT#2 MS
No Function Definition Laser Failure Alarm Indication Reserved For Module Debugging Reserved For Module Debugging Mounting Studs
Not Connected 5 6 7
Note 1: LVTTL logic output, with internal 1K pull-up resistor. Optical Signal-Detected: High; Optical Signal Loss: Low Note 2: LVPECL logic output, DC coupled internally (See Recommended Interface Circuit) Note 3: LVTTL logic input, with internal 1K pull-up resistor. Transmitter Disabled: High; Transmitter Enabled: Low Note 4: LVPECL logic input, AC coupled with internal termination (See Recommended Interface Circuit) Note 5: TTL logic output, pulled up by a 4.7-10K resistor on the host board. Laser Normal State: High; Laser Failure State: Low Note 6: Reserved for module tuning and compulsive for system application that any circuit doesn't be connected to them. Note 7: The mounting studs are provided for transceiver mechanical attachment to circuit board. They may also provide an optional connection of the transceiver to the equipment chassis ground. The holes in the circuit board must be tied to chassis ground. It is not recommended that the mounting studs be connected to signal ground.
Mechanical Design Outline
The form factor is 2x5/2x10 SFF with pigtail fiber. The pigtail fiber has a length of 520 - 550mm and 30mm minimum bending radius. The fiber connector type is SC/UPC. The mechanical design diagram is shown in Figure 7 and 8. (Dimension in mm)
4.81 0.05 10.16
0 10- 0.50-0.05
9.9 0.1
0 3.1-0.1
0.5
1.778 4x1.778(=7.112)
520~550
49.0 0.1
Label
Figure 7 FTM-9712P(T)-F20(G) Mechanical Design Outline Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 9 of 13 Doc No: DS3513000-1d
0.9
2x 5/2x10 SFF GEPON OLT Transceiver 20km transmission
FTM-9712P(T)-F(K)20(G) Preliminary Data Sheet Mar. 20, 2007
4.81 0.05 10.16
8.89
19.3
0 20-0.50 -0.05
5.40.3
9.9 0.1
0 3.1-0.1
0.5
2.90.3
1.778
2-1 9x1.778(=16.002)
520~550
49.0 0.1 13.5
Label
Figure 8 FTM-9712P(T)-K20(G) Mechanical Design Outline Table 7- Pigtail Fiber Characteristics
Parameter Mode Field Diameter Cladding Diameter Jacket Diameter Bending Radius of Pigtail Fiber Tension Force on Pigtail Fiber Pigtail Fiber Length Optical Return Loss (UPC type) -1490nm Optical Return Loss (APC type) -1490nm 520 50 60 30 1 550 Min. Typical 9 125 0.9 Max. Unit m m mm mm Kg mm dB dB
Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 10 of 13
0.9
12.30.3
MAX40.5
Doc No: DS3513000-1d
2x 5/2x10 SFF GEPON OLT Transceiver 20km transmission
FTM-9712P(T)-F(K)20(G) Preliminary Data Sheet Mar. 20, 2007
Ordering Information
Part No. FTM-9712P-F20 FTM-9712T-F20 FTM-9712P-K20 FTM-9712T-K20 FTM-9712P-F20G FTM-9712T-F20G FTM-9712P-K20G FTM-9712T-K20G 0C ~70C 1490nm(TX)/1310nm(RX), SC/APC Pigtailed 2x5 SFF for GEPON OLT,20km application, 0C ~70C 1490nm(TX)/1310nm(RX), SC/UPC Pigtailed 2x10 SFF for GEPON OLT, 20km application, 0C ~70C 1490nm(TX)/1310nm(RX), SC/APC Pigtailed 2x10 SFF for GEPON OLT, 20km application, 0C ~70C 1490nm(TX)/1310nm(RX), SC/UPC Pigtailed 2x5 SFF for GEPON OLT, 20km application, 0C ~70C, RoHS compliance 1490nm(TX)/1310nm(RX), SC/APC Pigtailed 2x5 SFF for GEPON OLT, 20km application, 0C ~70C, RoHS compliance 1490nm(TX)/1310nm(RX), SC/UPC Pigtailed 2x10 SFF for GEPON OLT, 20km application, 0C ~70C, RoHS compliance 1490nm(TX)/1310nm(RX), SC/APC Pigtailed 2x10 SFF for GEPON OLT, 20km application, 0C ~70C, RoHS compliance Product Description 1490nm(TX)/1310nm(RX), SC/UPC Pigtailed 2x5 SFF for GEPON OLT, 20km application,
Related Documents
For further information, please refer to the following documents: IEEE Std 802.3ahTM-2004
Obtaining Document
You can visit our website: http://www.fiberxon.com Or contact with Fiberxon, Inc. America Sales Office listed at the end of documentation to get the latest documents.
Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 11 of 13
Doc No: DS3513000-1d
2x 5/2x10 SFF GEPON OLT Transceiver 20km transmission
FTM-9712P(T)-F(K)20(G) Preliminary Data Sheet Mar. 20, 2007
Revision History
Reversion Pre 1a Initiate Zachary Lu Review Frank Zeng Approve Peter Tang 1. 2. 3. Pre 1b Zachary Lu Frank Zeng Peter Tang 1. 2. 3. 4. 5. 6. Pre 1c Zachary Lu Frank Zeng Peter Tang Subject Initial datasheet (Doc No. DS3513000-1a) Replace that interim version dated on Oct.23,2004 Defined with "Premium Version" to distinguish with "Functional Version" Combine P-F20 with P-K20 Mar.23,2006 Add new parts (APC connector) Add RoHS parts Update appearance picture in page 1 Modify "Laser Failure Alarm Voltage" in Table 4 Modify "Signal-Detected Voltage" in Table 5 Delete "Premium Version" Apr.28,2006 (Doc No. DS3513000-1b) Revised datasheet Modify "Receiver Threshold Settling Time" in Table 5 to MAX. 250ns (Doc No. DS3513000-1c) Pre 1d Jacob Cai Frank Zeng Peter Tang Revised datasheet 1. Correct the clerical error of product description in Order Information section. 2. Update Soldering Temperature and its notes in Table 2. (Doc No. DS3513000-1d) Mar. 20, 2007 Revised datasheet Release Date Jul.6,2005
Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 12 of 13
Doc No: DS3513000-1d
2x 5/2x10 SFF GEPON OLT Transceiver 20km transmission
FTM-9712P(T)-F(K)20(G) Preliminary Data Sheet Mar. 20, 2007
(c) Copyright Fiberxon Inc. 2007 All Rights Reserved. All information contained in this document is subject to change without notice. The products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. The information contained in this document does not affect or change Fiberxon's product specifications or warranties. Nothing in this document shall operate as an express or implied license or indemnity under the intellectual property rights of Fiberxon or third parties. All information contained in this document was obtained in specific environments, and is presented as an illustration. The results obtained in other operating environment may vary. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN "AS IS" BASIS. In no event will Fiberxon be liable for damages arising directly from any use of the information contained in this document. Contact U.S.A. Headquarters: 5201 Great America Parkway, Suite 350 Santa Clara, CA 95054 U. S. A. Tel: 408-562-6288 Fax: 408-562-6289 Or visit our website: http://www.fiberxon.com/
Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 13 of 13
Doc No: DS3513000-1d

▲Up To Search▲

Price & Availability of FTM-9712P-F20

	To Download FTM-9712P-F20 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .